Brass Resin Burner Brown

21.00

Brass Resin Burner Brown

The Brass Resin Burner Brown is used with Charcoal Discs to burn resin incense. You can also use it as a normal incense stick burner by adding sand to the burner.

Decorative and indispensable for purification rituals and incense ceremonies.

Attention. The Incense burner will get very hot and needs to be placed on a fireproof plate.

Please click here to return to the category.

In stock

SKU: PI16855/3 Categories: , ,

Description

 

Brass Resin Burner Brown

The Brass Resin Burner Brown is used with Charcoal Discs to burn resin incense. You can also use it as a normal incense stick burner by adding sand to the burner.

Decorative and indispensable for purification rituals and incense ceremonies.

Attention. The Incense burner will get very hot and needs to be placed on a fireproof plate.

Please click here to return to the category.

Light the charcoal and place on top of the burner. The charcoal is coated in an acellerant so it will light fast. Be carefull to store the charcoal properly to preserve the accelerant. Otherwise, the charcoal will dry out and you will be unable to light it.

Then, wait until the charcoal turns completely grey. This usually takes around ten minutes. Using a metal spoon, add a very small amount of resin on top of the hot charcoal releasing the fragrant incense smoke. You can repeat as desired until you exhaust the charcoal using multiple types of resins if desired. When you are finished, allow the charcoal to completely cool in the burner before discarding. When in doubt, dowse it with water.

Please click here to find our more about Resins

You may also like…

  • 6.50

    Gum Dammar Resin Incense

    Gum Dammar Resin Incense is also called dammar, or damar gum. It is a resin obtained from a particular family of trees in India and East Asia. Most Dammar is produced by tapping trees. However, some is collected in fossilised form on the ground

    Use this resin in charcoal burners and on incense burner sieves. Using a metal spoon, add a very small amount of resin on top of the hot charcoal releasing the fragrant incense smoke. Repeat as desired until the charcoal is exhausted. When finished, allow the charcoal to completely cool in the burner before discarding. When in doubt, dowse it with water.

    Please click here to return to the main category.

  • 6.50

    Gum Copal Resin Incense

    Gum Copal Resin Incense has had a wide variety of uses in both past and present times. Primarily used as an incense by ancient civilizations, it also found use as an early form of glue, and traditional medicine for cases such as dysentery, stomach pains, dizziness, and fright. It was often used in religious occasions in the form of sacrifices to deities typically designating the copal as food for the gods.

    Use this resin in charcoal burners and on incense burner sieves. Using a metal spoon, add a very small amount of resin on top of the hot charcoal releasing the fragrant incense smoke. You can repeat as desired until the charcoal is exhausted. When finished, allow the charcoal to completely cool in the burner before discarding. When in doubt, dowse it with water.

    Please click here to return to the main category.

  • 2.50

    Charcoal

    Charcoal is used for Shisha Hookah, incense cones and resins.  Long burning charcoal with less smoke.  The charcoal tablets are made out of extremely fine charcoal and pressed to make a clean, non-crumbly, non-exploding tablet.

    Use in charcoal burners. Using a metal spoon, add a very small amount of resin on top of the hot charcoal releasing the fragrant incense smoke. You can repeat as desired until the charcoal is exhausted. When finished, allow the charcoal to completely cool in the burner before discarding. When in doubt, dowse it with water.

    Please click here to return to the category.

Brass Resin Burner Brown

21.00

In stock